Page 6 - DAYLIGHT ITALIA 2020

DAYLIGHTITALIA 4

ANNEX II
Ecodesign requirements for non-directional household lamps

1. LAMP EFFICACY REQUIREMENTS
Incandescent lamps with S14, S15 or S19 caps shall be exempted from the efficacy
requirements of Stages 1 to 4 as defined in Article 3 of this Regulation, but not from Stages 5
and 6. The maximum rated power (P max ) for max a given rated luminous flux ( ø ) is provided in
Table 1. The exceptions to these requirements are listed in Table 2 and the correction factors
applicable to the maximum rated power are in Table 3.

TABLE 1
Maximum rated power (P ) for a given rated luminous flux ( ) (W)
Application date max
Clear lamps Non-clear lamps
Stages 1 to 5 0.8* (o,88 √ ø + 0,049 ø) 0.24 √ ø + 0,0103 ø
Stage 6 0.6* (o,88 √ ø + 0,049 ø) 0.24 √ ø + 0,0103 ø

TABLE 2 - EXCEPTIONS
Scope of the exception Maximum rated power (w)
Clear lamps 60 lm ≤ ø ≥ 950 lm in Stage1 P = 1,1* (0,88 √ ø + 0,049 ø)
max
Clear lamps 60 lm ≤ ø ≥ 725 lm in Stage2 P max = 1,1* (0,88 √ ø + 0,049 ø)
Clear lamps 60 lm ≤ ø ≥ 450 lm in Stage3 P max = 1,1* (0,88 √ ø + 0,049 ø)
Clear lamps with G9 or R7s cap in Stage6 P max = 0,8* (0,88 √ ø + 0,049 ø)
The correction factors in Table 3 are cumulative where appropriate and also applicable to the products covered by the exceptions of Table 2.

TABLE 3 - CORRECTION FACTORS
Maximum rated
Scope of correction
power (w)
Filament lamp requiring external power supply P max /1,06
Discharge lamp with cap GX53 P /0,75
max
non-clear lamp with colour rendering index ≥ 90 and P ≤ 0,5* (0,88 √ ø + 0,049 ø) P /0,85
max
Discharge lamp with colour rendering index ≥ 90 and Tc ≥ 5000 K P /0,76
max
non-clear lamp with second envelope and P ≤ 0,5* (0,88 √ ø + 0,049 ø) P max /0,95
Led lamp requiring external power supply P max /1,1

2. LAMP FUNCTIONALITY REQUIREMENTS
The lamp functionality requirements are set out in Table 4 for compact fluorescent lamps and
in Table 5 for lamps excluding compact fluorescent lamps and LED lamps.
Where the rated lamp lifetime is higher than 2 000 h, the Stage 1 requirements for the
parameters Rated lamp lifetime,Lamp Survival Factor and Lumen maintenance in Tables 4 and
5 are only applicable as from Stage 2.
For the purposes of testing the number of times the lamp can be switched on and off before
failure, the switching cycle shall consist of periods comprising 1 minute on and 3 minutes off,
while the other test conditions are defined according to Annex III. For the purposes of testing
lamp lifetime, lamp survival factor, lumen maintenance and premature failure, the standard
switching cycle according to Annex III shall be used.

TABLE 4 - FUNCTIONALITY REQUIREMENTS FOR COMPACT FLUORESCENT LAMPS
Functionality parameter Stage 1 Stage 5
Lamp survival factor at 6000h ≥ 0,50 ≥ 0,70
At 2 000 h: ≥ 88 %
At 2000 h: ≥ 85% (≥ 80% for a lamps ( ≥ 83 % for lamps
Lumen maintenanc
with second lamp envelope) with second lamp envelope)
At 6 000 h: ≥ 70 %
≥ half the lamp lifetime expressed
Number of switching cycles in hours ≥ lamp lifetime expressed in hours
before failure ≥ 10 000 if lamp starting time ≥ 30 000 if lamp starting time > 0,3 s
> 0,3 s